Conferences related to Insulator testing

Back to Top

2021 IEEE Photovoltaic Specialists Conference (PVSC)

Photovoltaic materials, devices, systems and related science and technology

2021 IEEE Pulsed Power Conference (PPC)

The Pulsed Power Conference is held on a biannual basis and serves as the principal forum forthe exchange of information on pulsed power technology and engineering.

2020 IEEE 70th Electronic Components and Technology Conference (ECTC)

ECTC is the premier international conference sponsored by the IEEE Components, Packaging and Manufacturing Society. ECTC paper comprise a wide spectrum of topics, including 3D packaging, electronic components, materials, assembly, interconnections, device and system packaging, optoelectronics, reliability, and simulation.

2020 IEEE International Conference on Plasma Science (ICOPS)

IEEE International Conference on Plasma Science (ICOPS) is an annual conference coordinated by the Plasma Science and Application Committee (PSAC) of the IEEE Nuclear & Plasma Sciences Society.

2020 IEEE International Instrumentation and Measurement Technology Conference (I2MTC)

The Conference focuses on all aspects of instrumentation and measurement science andtechnology research development and applications. The list of program topics includes but isnot limited to: Measurement Science & Education, Measurement Systems, Measurement DataAcquisition, Measurements of Physical Quantities, and Measurement Applications.

More Conferences

Periodicals related to Insulator testing

Back to Top

Advanced Packaging, IEEE Transactions on

The IEEE Transactions on Advanced Packaging has its focus on the modeling, design, and analysis of advanced electronic, photonic, sensors, and MEMS packaging.

Applied Superconductivity, IEEE Transactions on

Contains articles on the applications and other relevant technology. Electronic applications include analog and digital circuits employing thin films and active devices such as Josephson junctions. Power applications include magnet design as well asmotors, generators, and power transmission

Communications, IEEE Transactions on

Telephone, telegraphy, facsimile, and point-to-point television, by electromagnetic propagation, including radio; wire; aerial, underground, coaxial, and submarine cables; waveguides, communication satellites, and lasers; in marine, aeronautical, space and fixed station services; repeaters, radio relaying, signal storage, and regeneration; telecommunication error detection and correction; multiplexing and carrier techniques; communication switching systems; data communications; and communication theory. In addition to the above, ...

Components and Packaging Technologies, IEEE Transactions on

Component parts, hybrid microelectronics, materials, packaging techniques, and manufacturing technology.

Design & Test of Computers, IEEE

IEEE Design & Test of Computers offers original works describing the methods used to design and test electronic product hardware and supportive software. The magazine focuses on current and near-future practice, and includes tutorials, how-to articles, and real-world case studies. Topics include IC/module design, low-power design, electronic design automation, design/test verification, practical technology, and standards. IEEE Design & Test of ...

More Periodicals

Most published Xplore authors for Insulator testing

Back to Top

Xplore Articles related to Insulator testing

Back to Top

IEEE Draft Recommended Practice for Quality Control Testing of External Discharges on Stator Coils, Bars and Windings

IEEE P1799/D13, June 2012, 2012

This guide describes the procedure for quality control testing of external discharges on stator coils, bars and windings of large air-cooled ac electric machines.

Behaviour of Zinc Oxide surge arresters under pollution

IEEE Power Engineering Review, 1991


Performance of HV Transmission Line Insulators in Desert Conditions. Part IV. Study of Insulators at a Semi-Coastal Site in the Eastern Region of Saudi Arabia

IEEE Power Engineering Review, 1991


IEEE Draft Standard for Separable Insulated Connector Systems for Power Distribution Systems rated 2.5 kV through 35 kV

IEEE P386/D3.1, November 2015, 2015

Definitions, service conditions, ratings, interchangeable construction features, and tests are established for loadbreak and deadbreak separable insulated connector systems for use on power distribution systems rated 2.5 kV through 35 kV and 900 amps or less.

Provisional specification for insulator testing: Covering inspection and tests of high-tension line insulators of porcelain, for over 25,000 volts

Proceedings of the American Institute of Electrical Engineers, 1915

The present provisional specification was approved and recommended by the Power Transmission Committee of the American Institute of Electrical Engineers, Feb. 1915.

More Xplore Articles

Educational Resources on Insulator testing

Back to Top Videos

IMS 2011 Microapps - Digital Radio Testing Using an RF Channel Replicator
IMS 2012 Microapps - Virtual Flight Testing of Radar System Performance Daren McClearnon, Agilent EEsof
Synthetic Fuels to the Rescue?
Nanotechnology, we are already there: APEC 2013 KeyTalk with Dr. Terry Lowe
Millimeter-Wave Bandpass Filter Using High-Q Conical Inductors and MOM Capacitors: RFIC Interactive Forum
High Efficiency SHG in Heterogeneously Integrated GaAs Ring Resonators - Lin Chang - Closing Ceremony, IPC 2018
Mark I. Montrose: Testing for EMC Compliance
Tim Winters: Internet of Things IP Testing Service - IPv6 IoT InterOp-Ware Industry Forum Panel: WF IoT 2016
Standards Education: Strategic Standardization (English)
Be Prepared for the Test Challenges of IoT - MicroApps 2015 Keysight Technologies
MicroApps: Flexible Digital Modulation Testing for Satellite Regenerative Payloads (Agilent Technologies)
Sebastien Ziegler: F-Interop - IPv6 IoT InterOp-Ware Industry Forum Panel: WF IoT 2016
IMS 2015: Jonas Zmuidzinas - John Tucker Special Tribute - The High-Frequency Limits of SIS Receivers
RF-pFET in Fully Depleted SOI Demonstrates 420GHz FT: RFIC Industry Showcase 2017
NREL Wind Technology Center
Standards Education: Strategic Standardization (with Chinese subtitles)
5G mmW Phased Arrays - Future X Radio Panel Talk - Baljit Singh - Brooklyn 5G Summit 2018
Testing My New Robot Body
R. Jacob Baker - SSCS Chip Chat Podcast, Episode 4
Generating Stochastic Bits Using Tunable Quantum Systems - Erik Blair at INC 2019


Standards related to Insulator testing

Back to Top

IEEE Guide for Gas-Insulated Substations

This guide provides information of special relevance to the planning, design, testing, installation, operation and maintenance of gas-insulated substations(GIS) and equipment. This guide is intended to supplement IEEE Std C37-122- 1993(R2002). In general, this guide is applicable to all GIS above 52 kV. However the importance of the topics covered varies with application category. For example, issues related to advanced ...

IEEE Guide for Test Methods and Procedures to Evaluate the Electrical Performance of Insulators in Freezing Conditions

The guide specifies procedures for testing equipment when external insulation of the test object is subjected to combinations of contamination, ice, snow, or cold fog. The methods are applicable only to tests on equipment with a rated voltage above 1 kV.The guide specifies procedures for testing equipment when external insulation of the test object is subjected to combinations of contamination, ...

IEEE Guide for the Application, Maintenance, and Evaluation of Room Temperature Vulcanizing (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators

Guide to help utilities in application of RTV silicone rubber coatings for outdoor ceramic insulators. Guide covers details of these aspects. Guide to help testing personnel inevaluation of RTV silicone rubber coatings for outdoor ceramic insulators.

IEEE Recommended Practice for Maintenance of DC Overhead Contact Systems for Transit Systems

This recommended practice provides overhead contact system maintenance practices and procedures including maintenance techniques, site inspection and test procedures, and maintenance tolerances, for heavy rail, light rail, and trolley bus systems.

IEEE Recommended Practice for Specifying Distribution Composite Insulators (Suspension Type)

More Standards

Jobs related to Insulator testing

Back to Top